Fall of 2014

Haven't posted in a few months, here's what I've been up to recently.

EGR cooler cores on a Maxxforce 13, low temp for plugging (low flow) and the high temp for coolant consumption. Using the new tool is sure better than the old way of pulling the whole assembly for tear down.

Exhaust manifold on that same truck, this one has seen better days...

Pulled the trans in this Superduty for a clutch, once out on the ground what caught my attention wasn't the various broken clutch pieces floating around in the bell housing but the input shaft. The pilot bearing was completely gone at about 200K miles.

Pulled the injection pump on a 5.9 24 valve, the customer (FedEx) diagnosed and supplied the new pump. Well, they were wrong. Truck is still in the shop waiting for approval to continue on it I think.

I needed a precision measuring instrument recently.

This the clutch brake or low capacity inertia brake (LCIB) as Eaton calls it that they are using on Ultrashift + transmissions.

This was an intermittent power derate on a Cummins powered T300. Wire harness shorted to a fuel injection line.

Intermittent electrical problem with the amber warning lights and radio in this school bus, found a sticking relay. You can see evidence of water intrusion, I suspect this is not the only problem this will have as a result.

We were slow for awhile so I fab'd up a bracket to hold my creeper and air hose.

This is the result of a preset hub not setup correctly. 350 ft-lb spec and could be disassembled by hand. You can see the sheer amount of wear in the second picture. I measured an 1/8" gap between the roller and inner race holding it in that position. Pulled the diff to clean and inspect, rolling it over by hand revealed the faint sound of roller bearings hitting each other. It had spun the inner pinion bearing and it was so worn the rollers would fall into each other as they came up over the top.

This last Saturday I diagnosed a failed upstream NOX sensor on a Paccar MX, apparently there have been some problems, part number supersedes 3 times and the updated sensor is 4x the cost of the original. There is also software calibration that is supposed to fix NOX faults but as I found it only changes the fault from a P3805 to 3954 and 3958. Ran a regen to get the exhaust temp up enough for the NOX sensors to come online and the upstream sensor value was 0, downstream at ~14. Read through the 2 steps in troubleshooting (step 1 is check for fault codes, step 2 is also check for fault codes). Changed the sensor out and ran the regen again, upstream reading ~188.

Interesting day...

Not really what I expected to work on when I got up last Saturday morning. Burlington Northern 'track renewal system" with an 8V-92 coupled up to a transmission turning a hydraulic pump. I'm told it was built in 1984 and it's the only one they made.

Seemed to run smooth but heavy smoke at full throttle. Checked the usual suspects, intake was clear and the turbo was alright. Pulled the exhaust manifolds and rocker covers, started it up and moved the rack to bump the rpm's up (Throttle control is wide open or idle). Found #4 LH bank dumping smoke, still running just as smooth as can be. Swapped in a rebuilt injector and ran it up again before putting the manifolds back on. My hearing still isn't right!

So... An N14 again

My intimate familiarity with N14's payed off today... '99 Freighliner died on the freeway at Sunset. He coasted to Iowa street and came to a stop here. Nothing like working right in the middle of the road!

While Insite locked itself up and froze the computer I checked all the usual suspects. ECM fuses at the battery, cranking voltage (11.5 okay there), fuel in the tank, coolant etc... Once it decided it wanted to talk I found DTC 0254 ECM turns off fuel valve supply voltages. Interesting.

According to the troubleshooting an ECM draw of over 2 amps or measured voltage below 6 volts at pin 16 (Fuel shut off solenoid) will set the code. Found the ECM ground fuse blown. Replaced but the code stayed active and Insite will not allow you to clear engine shut down codes. The ECM has to detect that the problem is fixed but since it has shut off feed to the solenoid how do I tell it to reset? Hmm, jumper wire from the starter to the solenoid post for just a second and the code resets and goes inactive. Truck starts right up.

Why would the ECM draw over 2 amps I wonder? I bet if the solenoid was failing... Passed the ohms test but man it's hot if you put your hand on it. Checked it again 0.0 ohms. Yeah, that's not right. Went back to the shop and got a new solenoid. Checked the old again before taking it off and it's at 1.8 ohms (Spec is 6-12 if I remember correctly). Change it out and check it again just because and it's over 13 ohms. Truck starts up, no faults, no leaks, ice is on it's way to Concrete again. Solenoid was heating up and the current draw went up with it. ECM says woah wait a minute and shut's off power to the solenoid.

Fascinating thing is this truck had a new ECM and harness put in a year ago. I wonder if they were having trouble?

Last week of school

Just finished up a few things at school this week. Ended up off work after having the pin removed from my finger. Starting to heal up and gain some motion again. 5 degrees of movement in that joint. Therapist figures about a month before I have close to full range of motion in that hand again. What an interesting learning experience this has been... I think I'll avoid breaking any more bones in the future.

On to International's training now!

Week: 30
Total: 480

SPQ2014

Did a relative compression test on the International

Found the code on the 6.7 with IDS... That was a learning curve. Ford needs to update their software to the 21st century. Got a bit frustrated with it for a while.

Used the Modis on the Dodge to cycle the wipers and horn.

Fuel rated synflex hose because OE parts are what we do.

Learned a bit about Isuzu sensor wiring... Still haven't figured out why they need 4 ECT sensors to run a '94 model year engine. Wire harness chaffed on a clamp and the truck wouldn't idle right and gauges started doing odd things.

Week: 50
Total: 450

SPQ2014

Had a little re-wiring project on Saturday... 8 hours to re-wire the rear of the trailer and fix a broken wire in the front wall of the trailer. New everything from the cord back. Used Tectran shielded wire for everything and marine grade sealed splices. Sorry for the poor quality pictures.

I've been learning how the parts department works lately. Stocking shelves, labeling parts, did MSDS sheets for a few days. I filled in for the service writer on Friday also. That was interesting... I've decided that I'm not the best at understanding accents.

More ThermoKing APU work...

They're using an Ingersoll branded Yanmar engine which has a tendency to smoke when not serviced regularly as I found out when I ran one with the shop doors closed.

Went and helped my dad out for a bit and fought with the GPS. The line would drift a few inches in the time it took to get out and check the gearbox temps on the rototiller. Decided that the treeline was messing with the GPS signal.

Doing a fan test on a MaxxForce. Pulse width control is great when it works! I've learned that dust does not agree with these Horton fan clutches.

Week: 50
Total: 400

SPQ2014

We finished the measurements on the CAT 3176 this week. Learned about cylinder pack replacement rather than having a tech install the piston/rod in the liner. Truth be told I like the idea.

The motor's manual does not give a lot of specs as we found out.

Checking wrist pin and rocker for wear.

Removing valves to check the face and seat for wear.

Torquing the head bolts and setting valves.

I've had a few engines apart before but never one good enough to put back together so setting the valves etc... was new to me. Everything before I've pulled a piston and decided the engine was scrap metal. It's always been a visible failure without needing to go as far as checking clearances.

This is a coolant temperature circuit.

Week: 60
Total: 350